sample .tcf / .trd files

[alecjtaylor 0]

Hi all,

 

Does anyone know of any sample tcf/trd files that list all commands avaliable within a specific build of tuflow? I am limited to using 2011-09 build by my IT department and would like to be able to see a list of all commands rather than browsing the manual to find syntax of the lesser used commands.

 

Thanks for any help or advice

 

Alec

 

 

[par 0]

Hi Alec,

 

Apologies for the slow response.  If you open up a .tlf for a simulation, a list of specified and assumed commands is outputted.

 

An example is provided below from a 2011-09 simulation. 

 

Regards

Phil

 

!_______________________________________________________________________________
! BACKWARD COMPATIBILITY DEFAULTS COMMANDS
! Defaults ==  ! [ {} | PRE 2006-06-AA | PRE 2007-07-AA | PRE 2008-08 | PRE 2010 ]

!_______________________________________________________________________________
! GEOGRAPHIC REFERENCE COMMANDS
GIS Format == MIF
MI Projection == CoordSys Earth Projection 8, 104, "m", 177, 0, 0.9996, 500000, 10000000 Bounds (-7745844.29597, 2035.05676326) (8745844.29597, 19997964.9432)
SHP Projection ==
GIS Projection Check == ERROR
Snap Tolerance == 0.001

!_______________________________________________________________________________
! READ FILES
! The following Read Files (if any) were found:

!_______________________________________________________________________________
! 2D DOMAIN DEPENDENT COMMANDS
! Note:  Set / Read MI/GIS FC, PO, LP, GLO, IWL commands not shown - use check files to verify.
! Found 1 2D Domain(s)

Start 2D Domain == Domain_001
   Geometry Control File == C:\TUFLOW\Tutorial_Wiki\TUFLOW_MI\model\M01_5m_003.tgc
   BC Control File == C:\TUFLOW\Tutorial_Wiki\TUFLOW_MI\model\M01_5m_003.tbc
   Cell Wet/Dry Depth (m) == 0.002
   Cell Side Wet/Dry Depth (m) == 0.001
   ! Instability Water Level == <default>  ! ie. will use highest Zpt
   ! Morphology Control File ==  ! None specified
   ! AD Control File ==  ! None specified
End 2D Domain == Domain_001

!_______________________________________________________________________________
! FILE MANAGEMENT COMMANDS
! Estry Control File == <filename>.ecf  ! not specified
Write Check Files == C:\TUFLOW\Tutorial_Wiki\TUFLOW_MI\check\2d\M01_5m_003
Input Drive ==
Output Drive ==
Output Folder == C:\TUFLOW\Tutorial_Wiki\TUFLOW_MI\results\M01\2d\
Check MI Save Date == ERROR  ! [ {ERROR} | WARNING | OFF ]
Check MI Save Ext == .tab  ! [ {.tab} | <ext> ]
XF Files  == ON   ! Options [ ON | {OFF} ]

!_______________________________________________________________________________
! BC DATABASE GLOBAL SETTINGS COMMANDS
BC Database == C:\TUFLOW\Tutorial_Wiki\TUFLOW_MI\bc_dbase\bc_dbase.csv
BC Event Name ==
BC Event Source == <source_text> | <source_name>
BC Zero Flow == OFF  ! [ {OFF} | START | END | START and END ]

!_______________________________________________________________________________
! SIMULATION CONTROL COMMANDS
Start Time (h) == 0.
End Time (h) == 3.
First Sweep Direction == POSITIVE   ! Options [ AUTOMATIC | {POSITIVE} | NEGATIVE ]

!_______________________________________________________________________________
! BED RESISTANCE FORMAT COMMANDS
Bed Resistance Values == MANNING n   ! Options [ {MANNING n} | MANNING M | CHEZY ]
Bed Resistance Cell Sides == INTERROGATE   ! Options [ {AVERAGE n} | AVERAGE M ]
Change Zero Material Values to One == OFF   ! Options [ ON | {OFF} ]
Bed Resistance Depth Interpolation == SPLINE n  ! [ {SPLINE n} | LINEAR n | LINEAR M ]

!_______________________________________________________________________________
! GLOBAL FLOW CONSTRICTION (FC) COMMANDS

!_______________________________________________________________________________
! OUTPUT CONTROL AND FORMAT COMMANDS
Map Output Format == SMS   ! Options [ {SMS [ {} | HIGH RES [ {} | CORNERS ONLY ] ]} | SMS WITH LAND CELLS | RMA2 ]
Meshparts  == OFF   ! Options [ ON | {OFF} ]
Map Output Data Types == hVqd   ! Options [ {h} {V} q d W t E r F z1 ]
Store Maximums and Minimums == ON MAXIMUMS ONLY   ! Options [ ON | ON MAXIMUMS ONLY | {OFF} ]
Start Map Output (h) == 0.
Map Output Interval (s) == 300.
Map Cutoff Depth (m) == -1.
Maximum Velocity Cutoff Depth (m) == 0.1
Time Output Cutoff Depths == MAX

Mass Balance Output == ON   ! Options [ ON | {OFF} ]
Mass Balance Output Interval (s) == 300.

Mass Balance Corrector == OFF   ! Options [ ON | {OFF} ]
ZP Hazard Cutoff Depths ==  0.01 0.01 0.01

UK Hazard Formula == D*(V+0.5)+DF   ! Options [ D*(V+1.5) | {D*(V+0.5)+DF} ]
!UK Hazard Debris Factor == N/A
UK Hazard Land Use == CONSERVATIVE   ! Options [ PASTURE | WOODLAND | URBAN | {CONSERVATIVE} | NOT SET ]

!_______________________________________________________________________________
! SCREEN DISPLAY COMMANDS
Screen/Log Display Interval == 1   ! timesteps

!_______________________________________________________________________________
! TIME-SERIES OUTPUT COMMANDS
Start Time Series Output (PO and LPO) (h) == 0.
Time Series Output Interval (s) == 1.5
CSV Time == HOURS   ! Options [ {HOURS} | DAYS ]
Write PO Online == OFF   ! Options [ ON | {OFF} ]
Maximums and Minimums Time Series == OFF   ! Options [ ON | {OFF} ]

!_______________________________________________________________________________
! RESTART FILE COMMANDS
!Read Restart File ==  ! no restart file specified
Write Restart File Version == 1
!Write Restart File at Time (h) ==  ! not specified
!Write Restart File Interval (h) ==  ! not specified

!_______________________________________________________________________________
! WETTING AND DRYING COMMANDS
Wetting and Drying == ON   ! Options [ {ON} | ON NO SIDE CHECKS | OFF ]
Cell Side Checks == METHOD B

!_______________________________________________________________________________
! FREE-OVERFALL AND WEIR FLOW COMMANDS
Supercritical == ON   ! Options [ {ON} | OFF ]
Froude Check == 1.
Free Overfall == ON   ! Options [ {ON} | ON WITHOUT WEIRS | OFF ]
Free Overfall Factor == 0.6
Global Weir Factor == 1.
Shallow Depth Weir Factor Multiplier == 1.
Shallow Depth Weir Factor Cut Off Depth (m) == 0.0001
Shallow Depth Stability Approach == METHOD B
Shallow Depth Stability Factor == 0.
Shallow Depth Stability Cutoff (m) == 0.
Negative Depths In Water Level Output == INCLUDE
Negative Depth Approach == METHOD B
Negative Depth Values == -0.1, 0., 1., 1.

!_______________________________________________________________________________
! EDDY VISCOSITY COMMANDS
Viscosity Formulation == SMAGORINSKY   ! Options [ CONSTANT | {SMAGORINSKY} ]
Viscosity Coefficients == 0.2, 0.1  ! Variable, Constant components
Viscosity Approach == METHOD B

!_______________________________________________________________________________
! MISCELLANEOUS COMMANDS
Latitude == 0. ! degrees from equator (-ve for down under)
Check Inside Grid == ERROR

!_______________________________________________________________________________
! WATER LEVEL INSTABILITY DETECTION COMMANDS
Water Level Checks == ON   ! Options [ {ON} | OFF ]

!_______________________________________________________________________________
! BOUNDARY TREATMENT COMMANDS
HX Dry 1D Node Test == OFF   ! Options [ ON | {OFF} ]
Distribute HX Flows == OFF   ! Options [ ON | {OFF} ] - ON ONLY APPLIES TO ESTRY 1D SCHEME
Unused HX and SX Connections == ERROR   ! Options [ {ERROR} | WARNING ]
Adjust Head at Estry Interface == OFF   ! Options [ {ON} | ON VARIABLE | OFF ]
Oblique Boundary Method == ON
Boundary Treatment == METHOD A
HQ Boundary Approach == METHOD B
HQ Weighting Factor == 1.
Rainfall Boundaries == STEPPED
Rainfall Gauges == UNLIMITED PER CELL
Line Cell Selection == METHOD D
Link 2D2D Approach == METHOD B
Inside Region == METHOD B
SA Minimum Depth == -99999.
SA Proportion to Depth == OFF   ! Options [ {ON} | OFF ]
SX ZC Check == ON   ! Options [ ON | OFF | {0.3} ]
SX Head Adjustment == OFF   ! Options [ ON | {OFF} ]
HX ZC Check == ON   ! Options [ {ON} | OFF ]
Write x1D Check File == OFF   ! Write Check Files == ON must be also set  ! Options [ ON | {OFF} ]
VG Z Adjustment == MAX ZC   ! Options [ {ZC} | MAX ZC | ZH ]
Density of Air == 1.25
Density of Water == 1025.
Wind/Wave Shallow Depths == 0.2, 1.

!_______________________________________________________________________________
! WIND STRESS COMMANDS

!_______________________________________________________________________________
! WAVE RADIATION STRESS COMMANDS

Maximum Points == 500000
Maximum Vertices == 100000

[alecjtaylor 0]

Perfect!

 

Thanks for that Phil.